top of page

ปัญหาสีไหล (Sagging)

ปัญหาสีไหล (Sagging)

Sagging.jpg

สีไหล (Sagging)

สาเหตุ 1.ความหนืดที่ใช้ในการพ่นต่ำเกินไป 2.Thinner ที่ใช้มีการแห้งตัวช้าเกินไป 3.ความหนาของฟิล์มสีมากเกินไป และ/หรือฟิล์มสีไม่สม่ำเสมอ 4.ระยะระหว่างปืนกับชิ้นงานใกล้กันเกินไป การเดินปืนช้าเกินไปหรือAir Pressure ต่ำเกินไป 5.การควบคุมอุณหภูมิในห้อง Paintingต่ำเกินไป

การแก้ไข 1.เติมเนื้อสีให้ได้ความหนืดตาม Spec และปรับสภาพการพ่น(Painting condition) ตามกำหนด 2.ในกรณีที่ใช้ Thinner ตามที่แนะนำไว้ อาจเกิดจากการที่ปิดฝาภาชนะบรรจุ Thinner ไม่ดีพอทำให้ Solvent บางตัวที่เป็นประกอบใน Thinner ซึ่งระเหยได้ง่ายระเหยไปจากการเก็บ - ไม่ควรใช้ Thinner ที่ไม่ได้แนะนำ เนื่องจากอาจมีคุณสมบัติไม่เหมาะกับสีที่ใช้ 3.ฝึกฝนการเดินปืนพ่นโดยรักษาระยะห่างและแรงดันตลอดจนจังหวะการเคลื่อนที่ของปืนที่สม่ำเสมอ 4.เพิ่มระยะระหว่างปืนพ่นกับชิ้นงานให้ห่างประมาณ 1ฟุต ปรับการเดินปืนให้ช้าลง ตลอดจนปรับ Air Pressure ให้เหมาะสม 5.ควบคุมอุณหภูมิในห้องพ่นไม่ควรต่ำกว่า 23 °C

Sagging

Causes 1.Too low viscosity of spray application 2.Using too slow-evaporating thinner 3.Too thick and/or uneven paint film 4.Distance between spray gun and surface is too close or air pressure level is too low 5.Temperature control of paintng room is too low Solutions 1.Add paint compounds to achieve the viscosity suggested by specifications. Adjust the painting condition according to the requirements. 2.If the proper thinner is used, the cap of the thinner container may not be fully closed and some thinner mixture is evaporated. - Avoid using thinner that is not recommended by paint instructions as the compounds may not match the paint used. 3.Move the spray gun in consistency straight lines and remain at the same angles and distance from the surface with constant air spray pressure. 4.Keep the distance between spray gun and surface in 1 foot. Move the gun slower and adjust the air pressure to the correct level. 5.Temperature of the spray room should not be lower than 23°C

Resorces: www.nippon.co.th

bottom of page